Tree Trimming Tips from Tree Trimming Service Pros
If you have healthy trees and basic knowledge about tree trimming and pruning, it may not be necessary to hire a tree trimmer. You may be able do some tree work yourself if you have a basic knowledge of the subject. With the right information and some equipment, it is easy to maintain a tree’s health and appearance. You Tree Trimming Service can avoid common problems by performing routine maintenance. There are many tree trimming methods available, but you don’t have to be familiar with all of them. It’s not difficult to learn the basics. However, if you don’t have the time or are unable to maintain a large yard, you might consider hiring a professional tree trimming company like Evergreen Tree Services.
How to Trim and Prune Trees
Three main reasons are given for trimming trees.
1 Safety – A tree that has fallen or broken branches is a serious safety hazard. They can fall at any moment and should be removed immediately. Although you don’t want to make your tree look unnatural, it is better to remove dying branches before they become dangerous. If your tree branches grow near utility lines, the same applies. If this happens, contact your utility company to have the problem addressed. Tree limbs and branches account for 14% of all power outages. If branches are too close or you’re not able to trim them, it is best to avoid taking on this responsibility. This could cause power disruptions and possibly even harm you or others. While you can trim the tree to keep it from getting too close, professionals should be contacted.
2) Health Pruning trees can often save them from getting infected. Just start trimming the branches and limbs that have been damaged. You can increase airflow by trimming the crown of a tree, which can be very good for it. Also, you should trim branches that are rubbing or crossing each other as they can fall unexpectedly.
3) Aesthetics Tree pruning is a way to control its appearance and shape. You don’t want too much trimming. Over-trimming or pruning trees can cause serious damage.
Some general tips for trimming trees
It is best to trim trees during their dormant seasons. Pine trees are the only exception to this rule. They can be trimmed any time there is a hazard.
Pay attention to the size of each branch when removing it. Branch diameters greater than 10 cm should be left to professionals. It is best to leave it to professionals if you do decide to tackle it yourself.
Trim branches with:
- Neat angles
- Angles in V-shape
- Weak
Any branches with strong u-shaped angles should be kept. Your lateral branches should be kept between 1/2 to 3/4 the size of the stem. The final job should have a ratio between the tree’s height and the living crown of 2/3.
Prune branches as soon as they are young. This will make it easier and reduce scarring. You should not remove the branch collar or leave behind a large stub.
Tree Pruning Tips
- The removal of a tree crown
- For younger trees, it is important to maintain a consistent spacing between the lateral branches.
- Prune branches that cross or run into each other.
- You should not remove more than 1/4 inch of a living crown.
Growing a Tree Crown
- For pedestrians, raising the crown of a tree is a good way to provide clearance.
- Live branches should not exceed 2/3 of the tree’s height.
- Avoid removing too many branches from the bottom of the tree. This can cause the tree to become less strong.
Reduce a Tree Crown
- You can remove the entire branch if it requires more than half its foliage to be removed.
- Only cut down a tree’s crown if absolutely necessary.
- Any lateral branches less than 1/3 of the stem’s width should be pruned.
Tree Trimming Techniques
- These tree trimming techniques are important to remember.
- Begin by looking for the collar at the base of your branch. This collar is located at the base or the branch.
- The branch ridge is the one you should be looking for. It is located on the upper surface, parallel to the branch angle.
- You can cut the branch bar ridge.
- Your cut should be angled down away from the stem.
- Do not damage the collar of the branch.
This technique can be used on both dead and live branches.
For longer stems, use the three-cut technique:
- Place a notch on one side of the stem that faces away from the branch.
- Do a second cut above the branch’s ridge and inside the branch’s crotch.
- The third cut should be parallel to the branch bark edge through the stem. This will eliminate the stub.
